If you are planning to coat your own garage floor in Salt Lake City, a quartz aggregate epoxy system gives you a thick, textured, showroom quality finish without hiring a crew. This guide covers what Salt Lake City weather means for your pour, how to prep a local slab, what it costs and which of our kits fits your project.
Every kit ships from our shop in Queen Creek, Arizona, and comes with free phone support from the people who mix and pack it. Call 602.600.0781 with questions before, during or after your install.
Salt Lake City at a glance for epoxy work
| Typical July high | About 93°F |
| Typical January low | About 23°F |
| Average yearly snowfall | About 52 inches |
| Humidity | Low |
| Best pour window | Late May through mid September |
| Kits for a two car garage | 4 kits for 400 sq ft (1 kit = 100 sq ft) |
Temperatures and snowfall are rounded long term averages for the city and are meant for planning. Always check the forecast and measure your actual garage and slab temperature on pour day.
How Salt Lake City weather affects your epoxy pour
Summer afternoons in Salt Lake City average around 93°F, which puts many garages near or above the 90°F upper limit for application. Mid summer pours are possible if you start early and work in small batches, but spring and fall give you the full working time.
January lows near 23°F mean winter mornings can dip below the 41°F minimum. If you need to pour in the cold months, warm the garage for a day ahead so the slab, not just the air, is at temperature.
The dry air in Salt Lake City works in your favor during cure, though it also means the surface skins over faster in heat, so keep a wet edge as you spread.
Salt Lake City averages roughly 52 inches of snow a year, which means road salt, deicers and meltwater on the garage floor all winter. A sealed quartz epoxy surface keeps that brine out of the concrete and wipes clean instead of soaking in.
Best time of year to pour in Salt Lake City
For most Salt Lake City garages, the most forgiving window is late May through mid September. In that stretch you can usually count on the slab staying between 60°F and 85°F through the 72 hour cure, which gives you full working time and a consistent finish.
Prepping a Salt Lake City garage slab
Wasatch Front winters bring snow and heavy road salt, while summers are hot and dry. Late spring through early fall is the window, and primer helps on salted slabs.
Before anything else, do the water droplet test. Sprinkle water on the bare concrete. If it soaks in within about 30 seconds, the surface is ready to grind and coat. If it beads up, there is a sealer, paint or contamination that has to come off first.
For Salt Lake City garages that have seen years of salt and freeze thaw, we strongly recommend a primer under the epoxy. It seals porous, weathered concrete and gives the coating a better bond.
Our full step by step process is on the installation instructions page.
Which kit fits your Salt Lake City project
Indoor quartz sand epoxy self leveling floor kit. This is the kit for garages, workshops, basements and other interior concrete, in Marble Grey, Desert Grey or Black. The quartz aggregate gives a thicker, more textured and more slip resistant surface than standard garage floor paint or thin water based epoxy. It is made for indoor use and does not have strong UV protection, so keep it out of direct, all day sun.
Outdoor washed stone quartz epoxy floor kit. With as much sun as Salt Lake City gets, patios, walkways and porches should get the outdoor system rather than the indoor kit. It comes in four stone colors and covers up to 100 square feet per kit. The washed stone finish lets water pass through, so it is not a waterproofing membrane. Over a basement or living space, a separate waterproofing layer is needed underneath.
Tools. To spread and finish the coating you need a 22 inch squeegee with pole, a 20 inch defoaming roller and an extension pole for the roller. Our epoxy tool kit adds a tool bag, spiked shoes for walking on the wet coat and five finishing trowels.
How many kits you need
One kit covers 100 square feet at the target thickness of about one eighth inch. No guessing. Measure the length and width of the floor, multiply, divide by 100 and round up. A one car garage is about 200 square feet and takes 2 kits, a two car garage is about 400 square feet and takes 4 kits, and a two and a half car garage is about 500 square feet and takes 5 kits. Do not stretch coverage, since a thin coat will not level properly.
Questions Salt Lake City customers ask
When is the best time to epoxy a garage floor in Salt Lake City?
For most Salt Lake City garages the best window is late May through mid September. You want the garage between 41°F and 90°F, ideally 68°F to 77°F, with humidity under 65 percent.
How much does a DIY epoxy garage floor cost in Salt Lake City?
One kit covers 100 square feet, so a standard two car garage of 400 square feet takes 4 kits. At current pricing that is $996 in Marble Grey or Desert Grey and $1,200 in Black. If you do not own them, add about $95 for the squeegee, defoaming roller and extension pole, plus primer if your slab needs it. Professional installs are often quoted around $4 to $10 per square foot, which puts the same garage at roughly $1,600 to $4,000.
Can I use the indoor quartz epoxy kit on a patio in Salt Lake City?
The indoor kit is made for garages, shops and interior floors and does not have strong UV protection, so it can yellow in direct sun. For patios, porches and walkways, use our outdoor washed stone kit. It covers up to 100 square feet per kit, and because the washed stone finish lets water pass through, it is not a waterproofing membrane.
How long before I can park on my new floor?
Light foot traffic is fine after 24 hours, the coating reaches full cure around 72 hours, and you can drive and park on it after about 5 days. In cooler Salt Lake City garages below 55°F, allow extra time.
Will road salt damage an epoxy floor in Salt Lake City?
A sealed epoxy surface keeps salt brine out of the concrete, which is one of the main reasons people coat their garage in snow country. Sweep and rinse salt off regularly through winter and clean with a pH neutral cleaner rather than harsh chemicals.
Do I need a primer under the epoxy?
Primer is sold separately and is strongly recommended for older or porous concrete, slabs that were painted or sealed, floors with past moisture issues and any garage that sees heavy vehicle traffic. It seals the pores and gives the coating a stronger bond.
Why does epoxy bubble, and how do I stop it?
Concrete releases trapped air as it warms, and that air rises into the wet coating. Go over each section with a spiked defoaming roller 2 to 3 times while the epoxy is still wet, and pour when the slab is not heating up, such as early morning or evening.
How long does a DIY epoxy garage floor last?
Prep decides it more than anything else. A floor that was ground, cleaned and primed where needed, then coated at the full 100 square feet per kit, holds up for many years. Most floors that peel in the first year or two were coated over dust, oil, a sealer or old paint.
Ready to start your Salt Lake City garage floor
Talk to us about square footage, color and prep before you order. We are available Monday through Friday, 8am to 5pm Arizona time.
Nearby and similar climate guides: Denver, CO, Colorado Springs, CO, Aurora, CO, Reno, NV, Boise, ID. See all city guides.